harbor breeze ceiling fan blade replacement

Harbor breeze ceiling fan blade replacement manual#

of lead wire, and then cut the excess wire off with wire cutters (not included). Start at the TOP of the hanging ball on the downrod and measure 8 in. Take the lead wires and make sure you have pulled them all the way through the top of the downrod. If you decide to cut back the lead wires, it is suggested you do so in the following manner: Depending on the length of downrod you use, you may need to cut the lead wires back to simplify the wiring. Slide yoke cover (E) down until it rests on top of motor housing (D).Ĥ. Tighten set screws and then tighten nuts. Slip downrod (A) into yoke, align holes and re-install pin (L) and clip (M). Thread wires from motor housing (D) up through downrod (A)ģ. Insert downrod (A) through canopy (B), and yoke cover (E). Partially loosen preassembled set screws and nuts in yoke at top of motor housing (D).Ģ. Remove pin (L) and clip (M) from downrod (A).ġb. IMPORTANT: If using the angle mount, make sure open end of mounting bracket (C) is installed facing the higher point of the ceiling, and ensure the ceiling angle is not steeper than 19°.įor DOWNROD-STYLE FAN MOUNTING, proceed to step 1 below.įor CLOSEMOUNT-STYLE FAN MOUNTING, skip to page 10. *NOTE: It is very important you use the proper hardware when installing the mounting bracket (C) as this will support the fan. Secure mounting bracket (C) to outlet box (not included) using screws, spring washers and flat washers provided with the outlet box. Reattach top plate and yoke plate to motor housing (D) with lock washers (I) and motor screws (H) previously removed in Step 5.Ĩ.

Note: Make sure to completely secure each blade (J) before proceeding to the next.ħ. Attach blade (J) with 3 blade screws (AA) and fiber washers (BB). Align holes in blade (J) with holes in blade arm located inside of motor. Slide one blade (J) through one of the rectangular openings on center band of motor housing (D). Remove the yoke plate and top plate from motor housing (D).Ħ.

Remove 6 motor screws (H) and 6 lock washers (I) from top of motor housing (D). Partially loosen these 2 canopy mounting screws (G) and remove the other two save for later use.ĥ.

Temporarily raise canopy (B) to mounting bracket (C) and determine which 2 canopy mounting screws (G) align with slotted holes in canopy (B). Check to make sure blades (J) will be at least 30 in. Closemount mounting is more suitable for ceilings lower than 8 ft. A longer downrod is sometimes necessary to ensure proper blade clearance. Angle-style mounting is best suited for angled or vaulted ceilings. For taller ceilings you may want to use a longer downrod (not included). *Helpful Hint: Downrod-style mounting is best suited for ceilings 8 ft. IMPORTANT: If using the angle mount, check to make sure the ceiling angle is not steeper than 19°. Downrod mount (standard or angled ceiling) Turn off circuit breakers and wall switch to the fan supply line leads.Ī. Helpful Tools (not included): AC Tester Light, Tape Measure, Do-It-Yourself Wiring Handbook and Wire Cutters INITIAL INSTALLATIONġ. Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

If any part is missing or damaged, do not attempt to assemble the product. Compare parts with package contents list and hardware contents list. Place motor on carpet or on foam to avoid damage to finish.

Harbor breeze ceiling fan blade replacement manual#

User Manual (Operator/Owner/Guide) - (English)īefore beginning assembly of product, make sure all parts are present.Harbor Breeze 42003 Vue 44-in Brushed Nickel LED Indoor Residential Ceiling Fan with Light Kit Included (3-Blade) - Use Manual - Use Guide PDF.